Limiting traffic on bandwidth-hungry apps while leaving LAN traffic unlimited
Started by Ian
Limiting traffic on bandwidth-hungry apps while leaving LAN traffic unlimited 01 April 2006, 22:41
My BB comes in to an ADSL modem/router/firewall (Belkin 8630 - IP address = 192.168.2.1). Three PCs connect to the Belkin by wireless conection. Ip range for clients set on router is 192.168.2.1 - 192.168.2.10
I want to limit ougong traffic and incoming traffic (different limits for incoming and outgoing)on bandwidth hungry apps on 2 PCs while leaving the LAN traffic unlimited. I have been concentrating on one client to get that right before adding the other.
Rule #1: Protocol: TCP/UDP, Direction: Both, Rate: Unlimited, TCP/UDP Source: Range 192.168.2.1 - 192.168.2.10,/any Destination: Range 192.168.2.1 - 192.168.2.10/any ,any interface.
Rule #2: Protocol: TCP/UDP, Direction: Outgoing, Rate: 1514 b/s, TCP/UDP Source: 001150BAFAD4/any Destination: Any ip address/any, any interface.
Rule 1 is to give unlimited access to the LAN traffic between all clients and seems to be OK. When I access a video file from localhost to the one client with BWM service installed it reports what appears to be a reasonable amount of traffic.
Rule 2 is supposed to limit the outgoing traffic from one of the clients. However I can't see if it is working, and the rule seems to have no effect on the functioning of the client access to the internet playing World of Warcraft set at this very low level). Also no figures are reported on the sent/received when surfing from that client or when plaing WoW.
Is the rule written correctly?
Also the NIC for the client doesn't appear in the GUI list of interfaces when setting a rule. Should it?(this is why I set any interface as I couldn't select the one for the client).
When should I use the WAN interface?
Will BWM GUI on localhost automatically communicate with the BWM service on the client in this scenario?
I would appreciate any help. Thanks
Limiting traffic on bandwidth-hungry apps while leaving LAN traffic unlimited 01 April 2006, 23:30
Re: Limiting traffic on bandwidth-hungry apps while leaving LAN traffic unlimited 02 April 2006, 02:56
Registered: 12 years ago
Posts: 5 667
The Internet | Belkin ADSL/DHCP / | \ PC1 PC2 PC3If so, you will have to install the SoftPerfect Bandwidth Manager service on all the computers that require bandwidth management because you have no separate Windows based gateway. What you should do:
1. Install the bandwidth manager GUI component (standard installation package comes with two components: service and GUI) on the PC where you are sitting.
2. Install the bandwidth manager service component on the PCs that you can throttle.
3. Use the GUI installed on your PC at step (1). Specify the IP address of remote computer (2) where you have installed the service to connect to the service. Then configure its rules as follows :
Rule #1 (LAN): Protocol: TCP/UDP Direction: Both Rate: Unlimited Protocol: TCP/UDP Source: Range 192.168.2.1 - 192.168.2.255 Destination: Range 192.168.2.1 - 192.168.2.255 Interfaces: All interfaces Rule #2 (uploads): Protocol: TCP/UDP Direction: Out Rate: set as needed Protocol: TCP/UDP Source: local host Destination: Any Interfaces: All interfaces Rule #3 (downloads): Protocol: TCP/UDP Direction: In Rate: set as needed Protocol: TCP/UDP Source: Any Destination: local host Interfaces: All interfacesThere is no sense for you to use WAN interface since it is a built-in system adapter for wide area networks access. Should you have any questions please let me know
Re: Need help to configure 02 April 2006, 03:31
Unfortunately the Belkin DCHP does change the IP addresses sometimes. Is there a way round this other than turning Belkin DCHP off and me allocating the IP through Windows?
Thanks for your help.