All Forums
> NetWorx
> Current topic
Problem with network synchronization
Started by vanquisherr
Problem with network synchronization 15 April 2015, 21:24 |
Registered: 9 years ago Posts: 4 |
I installed NetWorx on the computers connected to my network. However, on my main computer, I am unable to view my other computers. On one of the other computers, I am able to view the network usage of all of the other computers.
On the main computer, I have fire wall turned off and I run AVG Antivirus. I have tried turning that off as well.
On the other computer (the one on which I can view the other users) I am running Avira antivirus with firewalls turned off as well.
Any ideas?
On the main computer, I have fire wall turned off and I run AVG Antivirus. I have tried turning that off as well.
On the other computer (the one on which I can view the other users) I am running Avira antivirus with firewalls turned off as well.
Any ideas?
Re: Problem with network synchronization 15 April 2015, 22:12 |
Admin Registered: 18 years ago Posts: 3 519 |
Some computers may have more than one network card. In this case you need to adjust Sync broadcast target address.
NetWorx relies on subnet broadcasts, so by changing the parameter above, you can ensure the broadcast messages are sent to a correct address. It's also worth mentioning that the sync only works within one subnet.
NetWorx relies on subnet broadcasts, so by changing the parameter above, you can ensure the broadcast messages are sent to a correct address. It's also worth mentioning that the sync only works within one subnet.
Re: Problem with network synchronization 15 April 2015, 23:28 |
Registered: 9 years ago Posts: 4 |
Which address do i sync to? From the main computer to the one that works and back and forth?
I used the ipv4 address i found from ipconfig 192.168.1.x
I have four network adapters in my Device manager. They are:
Bluetooth Device (Personal Area Network)
Bluetooth Device (RFCOMM Protocol TDI)
Realtek PCIe GBE Family Controller
Realtek RTL8723AE Wireless LAN 802.11n PCI-E NIC
I disabled my wireless and bluetooth adapters. The only one i have active is Local Arena Network. I am connected with my Ethernet cable. I am connected under All Ethernet Connections and i can't tick Ignore LAN Traffic
I used the ipv4 address i found from ipconfig 192.168.1.x
I have four network adapters in my Device manager. They are:
Bluetooth Device (Personal Area Network)
Bluetooth Device (RFCOMM Protocol TDI)
Realtek PCIe GBE Family Controller
Realtek RTL8723AE Wireless LAN 802.11n PCI-E NIC
I disabled my wireless and bluetooth adapters. The only one i have active is Local Arena Network. I am connected with my Ethernet cable. I am connected under All Ethernet Connections and i can't tick Ignore LAN Traffic
Re: Problem with network synchronization 16 April 2015, 10:43 |
Admin Registered: 18 years ago Posts: 3 519 |
Re: Problem with network synchronization 19 April 2015, 19:33 |
Registered: 9 years ago Posts: 4 |
I have tried doing this, and another computer on the network can now view information from all of the machines with networx installed.
On the main computer, i can view the information of this third computer, but not the second one which was able to view information from all computers.
To break it down, it has become like this:
I have three computers with networx:
The main computer, the second computer and the third one.
Main computer: Can view information from the third computer. Can't view information from the second one
Second computer: Was able to see information from all computers. But can only view information from the third one
Third computer: Able to see information from all three computers. Wasn't able to prior to target address sync
On the main computer, i can view the information of this third computer, but not the second one which was able to view information from all computers.
To break it down, it has become like this:
I have three computers with networx:
The main computer, the second computer and the third one.
Main computer: Can view information from the third computer. Can't view information from the second one
Second computer: Was able to see information from all computers. But can only view information from the third one
Third computer: Able to see information from all three computers. Wasn't able to prior to target address sync
Re: Problem with network synchronization 23 April 2015, 19:24 |
Admin Registered: 18 years ago Posts: 3 519 |
Re: Problem with network synchronization 24 April 2015, 19:45 |
Registered: 9 years ago Posts: 4 |
Re: Problem with network synchronization 27 April 2015, 13:27 |
Admin Registered: 18 years ago Posts: 3 519 |
A build with the experimental sync mechanism is available here.