OS WIN8 x64
installed version 3.4
make RAMDisk
go to disk managemet
create VHD & select save location on RAMDisk
Get BSOD
SoftPerfect RAM Disk
New beta version 3.4
Started by Andrew
Karim
New beta version 04 August 2013, 21:19 |
New beta version 08 August 2013, 21:53 |
Registered: 12 years ago Posts: 10 |
Haven't had any problems with the latest beta until today, when it BSOD on restarting. I'm not sure exactly when the BSOD happened as I wasn't watching, so it may have been when shutting down, during boot or after reaching the desktop.
As before, the dump refers to spvve.sys. Again this is on my brother's PC, with a single 1GB FAT32 Logon Mounted RAMDisk, which is compressed to only use 12KB on the HDD.
As before, the dump refers to spvve.sys. Again this is on my brother's PC, with a single 1GB FAT32 Logon Mounted RAMDisk, which is compressed to only use 12KB on the HDD.
shien
New version 3.4 19 August 2013, 17:44 |
I was using a RAMdisk of 16GB in version 3.4, but in order to freeze the program is in response without
After the uninstall
Error code = c0000098 was re-install version 3.3.3, but when you try to use the image that were available in 3.4
It will be displayed.
Whether there is no way to repair?
I want a button on the feature that allows you to back up only the data that has been updated
Operating System: Windows 7 Professional 64-bit (6.1, Build 7601) Service Pack 1 (7601.win7sp1_gdr.130708-1532)
Language: Japanese (Regional Setting: Japanese)
System Manufacturer: To Be Filled By O.E.M.
System Model: To Be Filled By O.E.M.
BIOS: BIOS Date: 01/17/13 12:08:38 Ver: 04.06.05
Processor: Intel(R) Core(TM) i7-3770 CPU @ 3.40GHz (8 CPUs), ~3.4GHz
Memory: 32768MB RAM
Available OS Memory: 32460MB RAM
Page File: 3786MB used, 61129MB available
Windows Dir: C:\Windows
DirectX Version: DirectX 11
DX Setup Parameters: Not found
User DPI Setting: Using System DPI
System DPI Setting: 96 DPI (100 percent)
DWM DPI Scaling: Disabled
DxDiag Version: 6.01.7601.17514 32bit Unicode
After the uninstall
Error code = c0000098 was re-install version 3.3.3, but when you try to use the image that were available in 3.4
It will be displayed.
Whether there is no way to repair?
I want a button on the feature that allows you to back up only the data that has been updated
Operating System: Windows 7 Professional 64-bit (6.1, Build 7601) Service Pack 1 (7601.win7sp1_gdr.130708-1532)
Language: Japanese (Regional Setting: Japanese)
System Manufacturer: To Be Filled By O.E.M.
System Model: To Be Filled By O.E.M.
BIOS: BIOS Date: 01/17/13 12:08:38 Ver: 04.06.05
Processor: Intel(R) Core(TM) i7-3770 CPU @ 3.40GHz (8 CPUs), ~3.4GHz
Memory: 32768MB RAM
Available OS Memory: 32460MB RAM
Page File: 3786MB used, 61129MB available
Windows Dir: C:\Windows
DirectX Version: DirectX 11
DX Setup Parameters: Not found
User DPI Setting: Using System DPI
System DPI Setting: 96 DPI (100 percent)
DWM DPI Scaling: Disabled
DxDiag Version: 6.01.7601.17514 32bit Unicode
Kees
New beta version 21 August 2013, 05:03 |